Exhibit 99.1

EVALUATION SUMMARY

AMPLIFY ENERGY CORP. INTERESTS

VARIOUS OIL AND GAS PROPERTIES IN THE UNITED STATES TOTAL PROVED RESERVES

AS OF DECEMBER 31, 2020

SEC PRICE CASE

EVALUATION SUMMARY

AMPLIFY ENERGY CORP. INTERESTS

VARIOUS OIL AND GAS PROPERTIES IN THE UNITED STATES TOTAL PROVED RESERVES

AS OF DECEMBER 31, 2020

SEC PRICE CASE

CAWLEY, GILLESPIE & ASSOCIATES, INC.

PETROLEUM CONSULTANTS

W. TODD BROOKER, P.E.

PRESIDENT

MATTHEW K. REGAN, P.E.

CAWLEY, GILLESPIE & ASSOCIATES, INC.

PETROLEUM CONSULTANTS

www.cgaus.com

As requested, this report was completed on January 18, 2021 for Amplify Energy Corp. (“Amplify”) for the purpose of public disclosure by Amplify in filings made with the SEC in accordance with the disclosure requirements set forth in the SEC regulations. We evaluated 100% of Amplify reserves, which are made up of oil and gas properties in Alabama, California, Louisiana, Oklahoma, Texas and Wyoming. This report, with an effective date of December 31, 2020, was prepared using constant prices and costs and conforms to the guidelines of the Securities and Exchange Commission (SEC). The results of this evaluation are presented below:

(Present Worth)

Amplify Energy Corp.

January 18, 2021

Page 2

Future revenue is prior to deducting state production taxes and ad valorem taxes. Future net cash flow is after deducting these taxes, future capital costs and operating expenses, but before consideration of federal income taxes. In accordance with SEC guidelines, the future net cash flow has been discounted at an annual rate of ten percent to determine its “present worth”. The present worth is shown to indicate the effect of time on the value of money and should not be construed as being the fair market value of the properties.

The oil reserves include oil and condensate. Oil and NGL volumes are expressed in barrels (42 U.S. gallons). Gas volumes are expressed in thousands of standard cubic feet (Mcf) at contract temperature and pressure base.

Our estimates are for proved reserves only and do not include any probable or possible reserves nor have any values been attributed to interest in acreage beyond the location for which undeveloped reserves have been estimated. The Proved Developed category is the summation of the Proved Developed Producing and Proved Developed Non-Producing estimates.

Hydrocarbon Pricing

The base oil and gas prices calculated for December 31, 2020 were $39.57 per barrel and $1.985 per MMBTU, respectively. As specified by the SEC, a company must use a 12-month average price, calculated as the unweighted arithmetic average of the first-day-of-the-month price for each month within the  12-month period prior to the end of the reporting period. The base oil price is based upon WTI-Cushing spot prices (EIA) during 2020 and the base gas price is based upon Henry Hub spot prices (Platt’s Gas Daily) during 2020.

The base prices were adjusted for differentials on a per-property basis, which may include local basis differentials, transportation, gas shrinkage, gas heating value (BTU content) and/or crude quality and gravity corrections. After these adjustments, the net realized prices over the life of the proved properties was estimated to be $36.621 per barrel for oil, $1.401 per MCF for gas and $14.751 per barrel for natural gas liquids. All economic factors were held constant in accordance with SEC guidelines.

Economic Parameters

Ownership was accepted as furnished and has not been independently confirmed. Oil and gas price differentials, gas shrinkage, ad valorem taxes, severance taxes, lease operating expenses and investments were calculated and prepared by Amplify and were thoroughly reviewed by us for accuracy and completeness. Lease operating expenses were calculated based on historical lease operating statements. All economic parameters, including lease operating expenses and investments, were held constant (not escalated) throughout the life of these properties.

SEC Conformance and Regulations

The reserve classifications and the economic considerations used herein conform to the criteria of the SEC as defined in the Appendix. The reserves and economics are predicated on regulatory agency classifications, rules, policies, laws, taxes and royalties currently in effect except as noted herein. Amplify’s operations may be subject to various levels of governmental controls and regulations. These controls and regulations may include matters relating to land tenure, drilling, production practices, environmental protection, marketing and pricing policies, royalties, various taxes and levies including income tax and are subject to change from time to time. Such changes in governmental regulations and policies may cause volumes of reserves actually recovered and amounts of income actually received to differ significantly from the estimated quantities.

Amplify Energy Corp.

January 18, 2021

Page 3

This evaluation includes 118 commercial proved undeveloped locations. There are 12 wells in the BAIROIL area (Wyoming), 17 wells in the BETA area (offshore California), 78 wells in the EGLFD area (Texas) and 11 wells in the M_LIME area (Oklahoma). Each of the drilling locations proposed conform to the proved undeveloped standards as set forth by the SEC. In our opinion, Amplify has indicated they have every intent to complete this development plan as scheduled. Furthermore, Amplify has indicated that they have the proper company staffing, financial backing and prior development success to ensure this development plan will be fully executed.

Reserve Estimation Methods

The methods employed in estimating reserves are described in the Appendix. Reserves for proved developed producing wells were estimated using production performance methods for the vast majority of properties. Certain  new producing  properties with very little production  history were forecast using a combination of production performance and analogy to offset production, both of which are considered to provide a relatively high degree of accuracy.

Non-producing and undeveloped reserve estimates were forecast using either volumetric or analogy methods, or a combination of both. These methods provide a relatively high degree of accuracy for predicting proved developed non-producing and proved undeveloped reserves for Amplify properties, due to the mature nature of their properties targeted for development and an abundance of subsurface control data. The assumptions, data, methods and procedures used herein are appropriate for the purpose served by this report.

General Discussion

The estimates and forecasts were based upon interpretations of data furnished by your office and available from our files. To some extent information from public records has been used to check and/or supplement these data. The basic engineering and geological data were subject to third party reservations and qualifications. Nothing has come to our attention, however, that would cause us to believe that we are not justified in relying on such data. All estimates represent our best judgment based on the data available at the time of preparation. Reserves estimates will generally be revised as additional geologic or engineering data become available or as economic conditions change. Moreover, estimates of reserves may increase or decrease as a result of future operations, effects of regulation by governmental agencies or geopolitical or economic risks. As a result, the estimates of oil and gas reserves have an intrinsic uncertainty. The reserves included in this report are therefore estimates only and should not be construed as being exact quantities. They may or may not be actually recovered, and if recovered, the revenues therefrom, and the actual costs related thereto, could be more or less than the estimated amounts.

An on-site field inspection of the properties has not been performed. The mechanical operation or condition of the wells and their related facilities have not been examined nor have the wells been tested by Cawley, Gillespie & Associates, Inc. Possible environmental liability related to the properties has not been investigated nor considered. The cost of plugging and the salvage value of equipment at abandonment have been included on commercial proved wells at the end of the economic life of the cases in the SEC pricing evaluation. The cost of plugging and salvage value of equipment at abandonment have not been included elsewhere herein.

Cawley, Gillespie & Associates, Inc. is a Texas Registered Engineering Firm (F-693), made up of independent registered professional engineers and geologists that have provided petroleum consulting services to the oil and gas industry for over 50 years. This evaluation was supervised by W. Todd Brooker, President at Cawley, Gillespie & Associates, Inc. and a State of Texas Licensed Professional Engineer (License #83462). We do not own an interest in the properties or Amplify Energy Corp. and are not employed on a contingent basis.

Amplify Energy Corp.

January 18, 2021

Page 4

We have used all methods and procedures that we consider necessary under the circumstances to prepare this report. Our work-papers and related data utilized in the preparation of these estimates are available in our office.

Yours very truly,

CAWLEY, GILLESPIE & ASSOCIATES, INC.

TEXAS REGISTERED ENGINEERING FIRM F-693

Matthew K. Regan, P.E. Vice President

APPENDIX

Methods Employed in the Estimation of Reserves

The four methods customarily employed in the estimation of reserves are (1) production performance, (2) material balance, (3) volumetric and (4) analogy. Most estimates, although based primarily on one method, utilize other methods depending on the nature and extent of the data available and the characteristics of the reservoirs.

Basic information includes production, pressure, geological and laboratory data. However, a large variation exists in the quality, quantity and types of information available on individual properties. Operators are generally required by regulatory authorities to file monthly production reports and may be required to measure and report periodically such data as well pressures, gas-oil ratios, well tests,  etc. As a general rule, an operator has complete discretion in obtaining and/or making available geological and engineering data. The resulting lack of uniformity in data renders impossible the application of identical methods to all properties, and may result in significant differences in the accuracy and reliability of estimates.

A brief discussion of each method, its basis, data requirements, applicability and generalization as to its relative degree of accuracy follows:

Production performance. This method employs graphical analyses of production data on the premise that all factors which have controlled the performance to date will continue to control and that historical trends can be extrapolated to predict future performance. The only information required is production history. Capacity production can usually be analyzed from graphs of rates versus  time  or cumulative production. This procedure is referred to as "decline curve" analysis.  Both capacity and restricted production can, in some  cases, be analyzed from graphs of producing rate relationships of the various production components. Reserve estimates obtained by this method are generally considered to have a relatively high degree of accuracy with the degree of accuracy increasing as production history accumulates.

Material balance. This method employs the analysis of the relationship of production and pressure performance on the premise that the reservoir volume and its initial hydrocarbon content are fixed and that this initial hydrocarbon volume and recoveries therefrom can be estimated by analyzing changes in pressure with respect to production relationships. This method requires reliable pressure and temperature data, production data, fluid analyses and knowledge of the nature of the reservoir.  The material balance method is applicable  to all reservoirs, but the time and expense required for its use is dependent on the nature of the reservoir and its fluids. Reserves for depletion type reservoirs can be estimated from graphs of pressures corrected for compressibility versus cumulative production, requiring only data that are usually available. Estimates for other reservoir types require extensive data and involve complex calculations most suited to computer models which makes this method generally applicable only to reservoirs where there is economic justification for its use. Reserve estimates obtained by this method are generally considered to have a degree of accuracy that is directly related to the complexity   of the reservoir and the quality and quantity of data available.

Volumetric. This method employs analyses of physical measurements of rock and fluid properties to calculate the volume of hydrocarbons in-place. The data required are well information sufficient to determine reservoir subsurface datum, thickness,  storage volume, fluid content and location. The volumetric method is most applicable to reservoirs which are not susceptible to analysis by production performance or material balance methods. These are most commonly newly developed and/or no-pressure depleting reservoirs. The amount of hydrocarbons in-place that can be recovered is not an integral part of the volumetric calculations but is an estimate inferred by other methods and a knowledge of the nature of the reservoir. Reserve estimates obtained by this method are generally considered to have a low degree of accuracy; but the degree of accuracy can be relatively high where rock quality and subsurface control is good and the nature of the reservoir is uncomplicated.

Analogy. This method, which employs experience and judgment to estimate reserves, is based on observations of similar situations and includes consideration of theoretical performance. The analogy method is a common approach used for “resource plays,” where an abundance of wells with similar production profiles facilitates the reliable estimation of future reserves with a relatively high degree of accuracy. The analogy method may also be applicable where the data are insufficient or so inconclusive that reliable reserve estimates cannot be made by other methods. Reserve estimates obtained in this manner are generally considered to have a relatively low degree of accuracy.

Much of the information used in the estimation of reserves is itself arrived at by the use of estimates. These estimates are subject to continuing change as additional information becomes available. Reserve estimates which presently appear to be correct may be found to contain substantial errors as time passes and new information is obtained about well and reservoir performance.

APPENDIX

Reserve Definitions and Classifications

The Securities and Exchange Commission, in SX Reg. 210.4-10 dated November 18, 1981, as amended on September 19, 1989 and January 1, 2010, requires adherence to the following definitions of oil and gas reserves:

"(22) Proved oil and gas reserves. Proved oil and gas reserves are those quantities of oil and gas, which, by analysis of geoscience and engineering data, can be estimated with reasonable certainty to be economically producible—from a given date forward, from known reservoirs, and under existing economic conditions, operating methods, and government regulations— prior to the time at which contracts providing the right to operate expire, unless evidence indicates that renewal is reasonably certain, regardless of whether deterministic or probabilistic methods are used for the estimation. The project to extract the hydrocarbons must have commenced or the operator must be reasonably certain that it will commence the project within a reasonable time.

"(i)      The area of a reservoir considered as proved includes: (A) The area identified by drilling and limited by fluid contacts, if any, and (B) Adjacent undrilled portions of the reservoir that can, with reasonable certainty, be judged to be continuous with it and to contain economically producible oil or gas on the basis of available geoscience and engineering data.

"(ii) In the absence of data on fluid contacts, proved quantities in a reservoir are limited by the lowest known hydrocarbons (LKH) as seen in a well penetration unless geoscience, engineering, or performance data and reliable technology  establishes  a lower contact with reasonable certainty.

"(iii)  Where direct observation from well penetrations has defined a highest known oil (HKO) elevation and the potential  exists for an associated gas cap, proved oil reserves may be assigned in the structurally higher portions of the reservoir only if geoscience, engineering, or performance data and reliable technology establish the higher contact with reasonable certainty.

"(iv)  Reserves which can be produced economically  through application  of improved recovery  techniques (including, but   not limited to, fluid injection) are included in the proved classification when: (A) Successful testing by a pilot project in an area of the reservoir with properties no more favorable than in the reservoir as a whole, the operation of an installed program in the reservoir or an analogous reservoir, or other evidence using reliable technology establishes the reasonable certainty of the engineering analysis on which the project or program was based; and (B) The project has been approved for development by all necessary parties and entities, including governmental entities.

"(v) Existing economic conditions include prices and costs at which economic producibility from a reservoir is to be determined. The price shall be the average price during the 12-month period prior to the ending date of the period covered by the report, determined as an unweighted arithmetic average of the first-day-of-the-month price for each month within such period, unless prices are defined by contractual arrangements, excluding escalations based upon future conditions.

"(6)     Developed oil and gas reserves. Developed oil and gas reserves are reserves of any category that can be expected to be recovered:

“(i)      Through existing wells with existing equipment and operating methods or in which the cost of the required equipment  is relatively minor compared to the cost of a new well; and

“(ii) Through installed extraction equipment and infrastructure operational at the time of the reserves  estimate  if  the extraction is by means not involving a well.

"(31) Undeveloped oil and gas reserves. Undeveloped  oil and gas reserves  are reserves  of any category  that  are  expected to be recovered from new wells on undrilled acreage, or from existing wells where a relatively major expenditure is required for recompletion.

“(i) Reserves on undrilled acreage shall be limited to those  directly  offsetting  development  spacing  areas  that  are  reasonably certain of production when drilled, unless evidence using reliable technology exists that establishes reasonable certainty of economic producibility at greater distances.

“(ii) Undrilled locations can be classified as having undeveloped reserves only if a development plan has been adopted indicating that they are scheduled to be drilled within five years, unless the specific circumstances, justify a longer time.

“(iii) Under no circumstances shall estimates for undeveloped reserves be attributable to any acreage  for  which  an  application of fluid injection or other improved recovery technique is contemplated, unless such techniques have been proved effective by actual projects in the same reservoir or an analogous reservoir, as defined in paragraph (a)(2) of this section, or by other evidence using reliable technology establishing reasonable certainty.

"(18)Probable reserves. Probable reserves are those additional reserves that are less certain to be recovered than proved reserves but which, together with proved reserves, are as likely as not to be recovered.

“(i)   When deterministic methods are used, it is as likely as not that actual remaining quantities recovered will exceed the    sum of estimated proved plus probable reserves. When probabilistic methods are used, there should be at least a 50% probability that the actual quantities recovered will equal or exceed the proved plus probable reserves estimates.

“(ii) Probable reserves may be assigned to areas of a reservoir adjacent to proved reserves where data  control  or  interpretations of available data are less certain, even if the interpreted reservoir continuity of structure or productivity does not meet the reasonable certainty criterion. Probable reserves may be assigned to areas that are structurally higher than the proved area if these areas are in communication with the proved reservoir.

“(iii)    Probable reserves estimates also include potential incremental quantities associated with a greater percentage recovery  of the hydrocarbons in place than assumed for proved reserves.

“(iv)See also guidelines in paragraphs (17)(iv) and (17)(vi) of this section (below).

exceeding proved plus probable plus possible reserves. When probabilistic methods are used, there should be at least a 10% probability that the total quantities ultimately recovered will equal or exceed the proved plus probable plus possible reserves estimates.

“(ii) Possible reserves may be assigned to areas of a reservoir adjacent to probable reserves where data control and interpretations of available data are progressively less certain. Frequently, this will be in areas where geoscience and engineering data are unable to define clearly the area and vertical limits of commercial production from the reservoir by a defined project.

“(iii)    Possible reserves also include incremental quantities associated with a greater percentage recovery of the hydrocarbons in place than the recovery quantities assumed for probable reserves.

“(iv) The proved plus probable and proved plus probable plus possible reserves estimates must be based on reasonable alternative technical and commercial interpretations within the reservoir or subject project that are clearly documented, including comparisons to results in successful similar projects.

“(v) Possible reserves may be assigned where geoscience and engineering data identify directly adjacent  portions  of a reservoir within the same accumulation that may be separated from proved areas by faults with displacement less than formation thickness or other geological discontinuities and that have not been penetrated by a wellbore, and the registrant believes that such adjacent portions are in communication with the known (proved) reservoir. Possible reserves may be assigned to areas that are structurally higher or lower than the proved area if these areas are in communication with the proved reservoir.

“(vi) Pursuant to paragraph (22)(iii) of this section (above), where direct observation has defined a highest known oil (HKO) elevation and the potential exists for an associated gas cap, proved oil reserves should be assigned in the structurally higher portions of the reservoir above the HKO only if the higher contact can be established with reasonable certainty through reliable technology. Portions of the reservoir that do not meet this reasonable certainty criterion may be assigned as probable and possible oil or gas based on reservoir fluid properties and pressure gradient interpretations.”

Instruction 4 of Item 2(b) of Securities and Exchange Commission Regulation S-K was revised January 1, 2010 to state that "a registrant engaged in oil and gas producing activities shall provide the information required by Subpart 1200 of Regulation S–K." This is relevant in that Instruction 2 to paragraph (a)(2) states: “The registrant is permitted, but not required, to disclose probable or possible reserves pursuant to paragraphs (a)(2)(iv) through (a)(2)(vii) of this Item.”

"(26) Reserves. Reserves are estimated remaining quantities of oil and gas and related substances anticipated to be  economically producible, as of a given date, by application of development projects to known accumulations. In addition, there must exist, or there must be a reasonable expectation that there will exist, the legal right to produce or a revenue interest in the production, installed means of delivering oil and gas or related substances to market, and all permits and financing required to implement the project.

“Note to paragraph (26): Reserves should not be assigned to adjacent reservoirs isolated by major, potentially sealing, faults  until those reservoirs are penetrated and evaluated as economically producible. Reserves should not be assigned to areas that are clearly separated from a known accumulation by a non-productive reservoir (i.e., absence of reservoir, structurally low reservoir, or negative test results). Such areas may contain prospective resources (i.e., potentially recoverable resources from undiscovered accumulations).”

CAWLEY, GILLESPIE & ASSOCIATES, INC.

PETROLEUM CONSULTANTS

Professional Qualifications of Primary Technical Person

The evaluation summarized by this report was conducted by a proficient team of geologists and reservoir engineers who integrate geological, geophysical, engineering and economic data to produce high quality reserve estimates and economic forecasts. This report was supervised by Todd Brooker, President of Cawley, Gillespie & Associates (CG&A).

Prior to joining CG&A, Mr. Brooker worked in Gulf of Mexico drilling and production engineering at Chevron. Mr. Brooker has been an employee of CG&A since 1992. His responsibilities include reserve and economic evaluations, fair market valuations, field studies, pipeline resource studies and acquisition/divestiture analysis. His reserve reports are routinely used for public company SEC disclosures. His experience includes significant projects in both conventional and unconventional resources in every major U.S. producing basin and abroad, including oil and gas shale plays, coalbed methane fields, waterfloods and complex, faulted structures.

Mr. Brooker graduated with honors from the University of Texas at Austin in 1989 with a Bachelor of Science degree in Petroleum Engineering, and is a registered Professional Engineer in the State of Texas. He is also a member of the Society of Petroleum Engineers (SPE) and the Society of Petroleum Evaluation Engineers (SPEE).

Based on his educational background, professional training and more than 20 years of experience, Mr. Brooker and CG&A continue to deliver professional, ethical and reliable engineering and geological services to the petroleum industry.

CAWLEY, GILLESPIE & ASSOCIATES, INC.

TEXAS REGISTERED ENGINEERING FIRM F-693